The C&H Precision plates are designed, manufactured and shipped from our small family owned business in Coastal Georgia. The screw head is just small enough to make these work. This Product: V4 MIL/LEO Adapter Steiner MPS Fits GLOCK MOS (STEEL) - 64.95. I thought I'd get some and see how they fit. Note: I discovered the screw head size difference after my previous post. The C&H Precision plates are designed, manufactured, and shipped from our small family-owned business. Replacement Screw Kit-GL-DPP/EFLX - 7.95. If you notice on the parts drawing at the below link, the screw head diameter is smaller than the other 6-32 screws. This Product: V4 MIL/LEO Adapter Leupold Delta Point Pro / EOTech EFLX Fits GLOCK MOS - 76.95. No big deal, clean them with alcohol and hit them with flat black. Approved for duty use by over 600 Local, State, Federal and US Military units, this adapter plate will ensure your red dot stays on your slide where it’s suppose to be. The CHPWS GLOCK MOS adapter plate is the most rugged, reliable, and trusted red dot adapter plate on the market today. The disadvantage is is you have to paint the heads of the screws. CH Precision GLOCK MOS Holosun 509T Adapter Plate. To me, the big advantage of these are they are the same size Torx bit as the Glock plate and it's a Torx. I thought I'd post what the 3/8 Torx look like on the RMR plate with the Trijicon "sealing plate".Īs as you can see, they're pretty much a perfect fit. If 3/8 is what you've got, well, mine haven't unscrewed yet. If you're set up to start with longer and cut them back, I'd do so just so you have the best setup. They work fine, but they could stand to be a little deeper. Best bet would be to get some 1/2" ones and cut them back. So 3/8 will be a little short (.375), 7/16 (.4375 - if you can find them) are a little long. Better than my pistol from the beginning of this month! They say it's weaker, but I think the older frying pan finish was the pinnacle of Glock finishes.I agree, my old 2 letter 3 digit serial number still looks good from 1991. Moreso than my 4's, and I noticed it on my 4's more than on my frying pan 3's I used to have. notice my 5's finish seem to be a little weaker as well, it's not a big deal or anything, but I notice it around holster rub areas. It just surprised me when I came in from the range on Thursday how worn it already was. It's not that it really matters, as this gun will probably become my EDC pistol and will have wear in the next few years. ( stopped keeping track of rounds in 2014 18k ) My G17.4 that I used for competition for years isn't worn this bad. The 507K, which the V4 Series plate is also with, substitutes a 2-MOA dot encircled by a 32-MOA ring.Has anyone noticed the finish on the Gen 5s just isn't holding up as good as the previous generations? Today my G19.5MOS is 3 weeks old. V4 MIL/LEO Adapter Leupold Delta Point Pro / EOTech EFLX Fits GLOCK MOS. Ultra-light, the 407K weighs only one ounce. The C&H Precision plates are designed, manufactured and shipped from our small family owned business in Coastal Georgia. Housing in 7075-T6 aluminum, the 407K features a 6-MOA aiming point, up to 50,000 hours of battery life powered by one CR1632 cell, and the “Shake Awake” function. This variant of the V4 Series is designed for Holosun 407K and 507K red-dot sights. Each plate is precision machined to the tightest tolerances on. The adapter plate hardware is made from stainless steel to increase corrosion resistance. This Product: V4 MIL/LEO Adapter Steiner MPS Fits GLOCK MOS (STEEL) - 64.95. Grab a C&H Precision Glock 43X/48 MOS Optic Adapter Plates for RMR, RMRcc, EPS, and 407K/507K from AT3 Tactical. The company’s industry-leading thread engagement - six to seven full revolutions - ensures that the MRD will remain securely fastened to the adapter plate, and the gun, during recoil. GLOCK MOS: G17, G19, G22, G23, G34, G35, G40, G41, G45, G47Ĭ&H Precision emphasizes that the adapter’s plate material isn’t the key to effective MRD retention - it’s the threading.Industry-leading thread engagement for increased MRD retention.Patent-pending replacement stainless-steel mounting hardware.These screws allow you to mount the RDS (red-dot system) to the V4 plate, changing the mounting hardware without replacing the adapter plate. To meet the demand for superior adapter plates, C&H Precision introduced the V4 Series for GLOCK MOS full size pistols, featuring C&H’s patent-pending replaceable stainless-steel T-Nuts and Torx-head screws. However, OEM mounting plates are not always satisfactory. As part of the MOS, the Glock pistol has a cut in the slide designed to accommodate optics, using a series of adapter plates. The Modular Optic System, or MOS, allows Glock handguns to attach MRD (miniature red-dot) sighting systems.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |